Thursday 21 June 2012

Vibration Analysis

Vibration Analysis
Vibration Analysis

Description of vibration


Shown in the diagram is the representation of a shaft with an out of balance in the form of a key. The graph plots the relative vertical displacement of a point on the disc.
The total vertical movement is called the Peak to Peak Displacement of the vibration. This is an indication of the amount of lateral movement of the machine and is a good indication of the amount of out of balance in a machine when the value is compared to a standard for that machine. This parameter is often used when balancing.
The Vibration Velocity is the speed of movement of this point, being highest as the point passes through its at rest position. It gives a good guide to the amount of energy being generated by the vibrating object. This energy usually results in wear and eventual failure. The amount of energy is proportional to the square of the velocity of vibration. Velocity, being a good indication of the amount of wear taking place in a machine is a used exclusively in monitoring systems.
For analysis purposes the r.m.s value is used.
For very low speed machines where the velocity is low the displacement may be used instead.
The Vibration Frequency is the time taken to complete one cycle. The shaft above is said to have a fundamental frequency equal to the shaft rotational velocity i.e.
R.P.M / 60 = Fundamental frequency = 1 / Periodic time
There is a formula for working out the frequency that a particular vibration is occurring from knowing only the displacement and the velocity.
Frequency = 0.45 x Vibration Velocity (mils/sec r.m.s)/ Vibration Displacement (mils peak to peak)
The equation is true only when the majority of the vibration occurs at one frequency. In reality machines vibrate in a much more complex way with vibration occurring at several frequencies. By analysis of the frequency at which each of the vibrations are occurring it is possible to ascertain whether they are being generated from with the or externally. By further analysis it is possible to locate the source of vibration within complex machinery.
Vibration phase can be defined as the angular relationship between the positions of maximum vibration and some fixed point on a rotating shaft at any instant.
It is useful during balancing.

Vibration measurement units

    There are three different ways of expressing vibration measurements
    1. Peak to Peak
    2. Half Peak (or Peak)
    3. Root Mean Square
they are related as follows
R.M.S. =Peak to Peak/2.83
Half Peak Values = Peak to Peak/2
Units may be in mils (1x 10-3 inches) or microns (1x 10-3 millimetres) and they may be converted as follows 1 mil =25.4 microns

Causes of vibration

    Typical causes could be
    • Out of balance
    • Misalignment
    • Damaged or worn bearings
    • Damaged or worn teeth
    • Resonance, loose components
    • Bending or eccentricity
    • Electromagnetic effects
    • Unequal thermal effects
    • Aerodynamic forces
    • Hydraulic forces
    • Bad belt drives
    • Oil whirl
    • Reciprocating forces
The great majority of the above create a vibration at a multiple of the fundamental. The Vibrations source identification table allows identification of the cause.
    Sequence of analysis
    1. Assemble equipment
    2. record operational parameters of machine- lubricating oil temperature, load, history of mal operation, work done
    3. Run machine until it reaches normal operating temperature
    4. Take readings at designated points. Analyse frequency of any high readings
    5. If possible measure vibration at different speeds
    6. Note changes in temperature, load etc. during measurement period
    7. If possible double check readings
    8. Determine source of vibration using identification table
    9. Remedy fault
Additional information can be gained by measuring vibration of the shaft itself. This may be done using a Teflon tipped pick up or a piece of hardwood.
    Causes of vibration other than initial out of balance
    • Non-periodic erratic vibrations can often be sourced to damaged or worn anti friction bearings. Where displacement of inner and outer race occurs then axial vibration at fundamental can occur. If the bearing is not concentric to the shaft then a vibration occurs as an out of balance
    • Where a moving component on a rotating member occurs an erratic fundamental frequency occurs. Balancing will only give temporary relief and indeed may lead to a worsening of the situation
    • Synchronous oil whirl occurs when the oil whirl in a bearing is at the same frequency as the fundamental. Analysis over a period will find a steadily worsening vibration which will begin to reduce if the speed of the machine is dropped, and then increase again when brought back to original speed. In this case the bearing clearance may be too large
    • Half speed oil whirl is indicated by a superimposed wave form at half fundamental on the total wave form. Varying oil temperature and pressures normally rectify but it may be necessary to increase bearing load by reducing bearing surface
    • Shafts may sometimes bend due to thermal asymmetry. Vibration will vary with temperature. If unequal thermal effects are present then they may be determined by taking displacement and phase measurements during a set of controlled 'heating up' and 'cooling down' periods. If they are plotted on an Argand diagram they will appear as so.
      Thermal effects may occur due to the following reasons.
      1. Non-homogenous forging of the rotor causing uneven bi-metallic expansion
      2. Uneven machining of the rotor forging
      3. Parts of the rotating element is restrained from expansion
      4. Friction effects due to parts rubbing
      5. Uneven ventilation
      Compromise or thermal balancing may be used to help alleviate the problem but these should only be carried out by specialised personnel
    • Double frequency vibration can have many different sources such as
      1. Non-isotropic characteristics of a rotor or shaft e.g. grooves, key ways, slots etc. causing the shaft to have two perpendicular stiffness' resulting in two cyclic deflections for one complete revolution. This can only be remedied by cutting two slots to even the stiffness.
      2. Electromagnetic effects most significant in the laminations. Only present when energised, increasing pressure on laminations can cure
      3. Machines with separate bearing housings which are not aligned can have vibration at 1,2 or 3 times fundamental. Indicated by large axial vibration component at pedestal.
      4. Bad belt drives give 1,2,3,4 harmonics which may not remain constant. Where the belt drive gives a speed change between driver and driven machines vibration can occur at a frequency corresponding to some multiple of both fundamental frequencies.
      5. Reciprocating parts can give multiple fundamental vibrations, only by redesign can this be cured, Diesel engine can vibrate at 2 x fundamental known as the forcing frequency caused y the action of the crank moving the piston rod. The travel of the piston is not entirely smooth and a slowing and speeding up occurs about the middle of the stroke and is governed by the ratio of crank throw to piston rod length. It may be counteracted by the use of balancers.
      6. Looseness
    • Three per revolution vibrations
      1. Sleeve bearing worn in a triangular fashion-unusual
      2. Poor belt drives
      3. Higher frequency vibrations can be caused by
        1. Badly mating or worn gears giving very high frequencies
        2. Aerodynamic and hydraulic forces will produce high frequency vibrations. If a fan is the source then the frequency will be at blade number x fundamental and may be caused by
          1. Unequal pitch of blades giving unequal axial vibration
          2. Blade vibrations as the blades operate at a resonant frequency
          3. Pipework and ducting can cause gas or liquid flows to produce a vibration at resonance
          4. Cavitation or oil pockets may produce high frequency resonant vibrations
          5. Wheels on turbine spindles can cause vibration
      4. Odd harmonics can sometimes be caused by worn components. Usually at fundamental the waveform may be erratic and irregular i.e. non- sinusoidal

Determination of rolling element bearing wear using vibration acceleration as the parameter

The condition of rolling element bearings can be accurately determined by taking measurements of acceleration in terms of 'g' peak. Irregularities in newly fitted bearings lead to dynamic load and vibration detectable as accelerations in a vibration monitor. It is the magnitude and frequency span that determines the condition of the bearing. Accelerations due to a failing bearing will fall between 1 - 5kHz.
When judging the condition of a bearing it is important to take into account the speed at which it is running. Acceleration is proportional to the square of the rotational frequency. Therefore a slow running machine would give accelerations lower then a higher speed running machine for the same bearing condition.
The following table can be used as a rough guide.
State of rolling element bearing Level of acceleration 'g' peak (in range 1 - 5 kHz)
Satisfactory 1
Bearing failing 2 -5
Renew bearing urgently 5+
This does not apply to journal, plain or sleeve bearings
    Care must be taken with some the following machinery as they can naturally generate vibration in the 1 - 5 kHz range
    • Gearboxes ( i.e. gear teeth frequencies)
    • High speed screw compressors - lobe passing frequency
    • High speed turbines - blade passing frequency.
    • Cavitation in pumps
    • etc
Pattern of frequency of failing rolling element bearing.
If the peak appears to be isolated then other possible sources such as gear teeth should be investigated.
If the vibration occurs over a broad band then it is probably due to bearing failure. Cavitation can be determined as the source by checking the locality of the source. Whether bearing housing or pump casing. Also the discharge valve may be partially closed which should reduce the cavitation and the vibration.

Method for assessing condition of rolling element bearing.

    1. Measure radial acceleration at each bearing in vertical and horizontal directions and record the lowest value
    2. evaluate condition of bearing against set levels
    3. If over 1 ( minimum that can be reliably analysed) then use harmonic analyser to check frequency range
    4. put harmonic analyser in 'fine' mode and check spread of vibration, if over 500 Hz the probably bearing failure
    5. Repeat as check '4' on velocity mode
The effect of main engine revolutions on vibration readings
Generally the increase in vibration will be small, their are some cases however were a noticeable rise occurs. This may be due to a flexible bed plate or harmonics.
Effect of flexible and semi flexible bedplates on vibration
Prop revs/min Vibration in mils/s r.m.s
Machine on semi-flexible bed plate Machine on very flexible bed plate
60 10 20
70 20 40
80 30 60
90 42 46
100 55 112
110 70 143
120 90 180
If the vibration from a machine only is required then readings should be take below 50 r.p.m or better at anchor. Readings may be taken under full sea going conditions as long as they are continues to do so. In many circumstances it is the trend over a period of time that is the important factor rather than a set of readings at any one instant. In this way the warning levels set for a machine may be safely increased.
All mineral oil separators must be within the good limit
Chart of vibration displacement against frequency for normal machines

5 comments:

  1. I appreciate all of the information that you have shared. Thank you for the hard work!

    - The Vibration Analysis

    ReplyDelete
    Replies
    1. I am the author of most of the work on your website against which you are making financial gain. If you do not gain permission or remove it I will take further action. My site is non-commercial, I note you have placed content from marinediesels.info which is a commercial site, you are in breach of his copyright and as such ne may not be as generous in allowing you time to remove his work before taking further action.
      brian

      Delete
  2. I am the author of most of the work on your website against which you are making financial gain. If you do not gain permission or remove it I will take further action. My site is non-commercial, I note you have placed content from marinediesels.info which is a commercial site, you are in breach of his copyright and as such ne may not be as generous in allowing you time to remove his work before taking further action.
    brian

    ReplyDelete
  3. I am the author of most of the work on your website against which you are making financial gain. If you do not gain permission or remove it I will take further action. My site is non-commercial, I note you have placed content from marinediesels.info which is a commercial site, you are in breach of his copyright and as such ne may not be as generous in allowing you time to remove his work before taking further action.
    brian

    ReplyDelete